Đào tạo API 570





Introduction
Certified API 570 Piping inspectors must have a broad knowledge base relating to maintenance, inspection, alteration and repair of in-service metallic piping systems. The API 570 examination is designed to determine if applicants have such knowledge.
This certification program benefits employers and the industry as a whole by helping to:

Provide a continued high level of safety through the use of inspectors specialized in process piping.
Improve management control of process unit inspection, repair, alteration and rerating.
Reduce the potential for inspection delays resulting from regulatory requirements.

Training Objectives
The aim of this comprehensive preparatory course is to provide the delegates with knowledge on how to easily PASS and obtain the API 570 authorized piping inspector certification as well as:

Identify the various design conditions of piping components, materials, fabrication, assembly, erection, inspection, examination and testing as well as demonstrate non-destructive test methods.
Employ post weld heat treatment; identify the Charpy impact testing, also the working pressure and temperature requirements for pipework flanges.
Positive Material Identification (PMI) requirements and procedures.
Carryout welding discontinuities and discuss ASME section IX, WPS, WPQ and PQR.

Who should attend
This training course is suitable to a wide range of professionals but will greatly benefit:

Professionals who are interested in getting the API 570 – Authorised Piping Inspectors Certification

Piping Inspection Engineers
Plant Inspectors
Corrosion Engineers
QA/QC Inspectors
Asset Integrity Engineers
Project Engineers
Maintenance Engineers
Welding Engineers/Inspectors
NDT Engineers/Inspectors

Daily Agenda

Day ONE

API 570 (Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems)

Scope & Definitions
Owner/user inspection organization
API authorized piping inspector qualification and certification
Inspection and testing practices
Risk-based inspection
Preparation for inspection
Inspection for specific types of corrosion and cracking
Types of inspection and surveillance
Thickness measurement location
Thickness measurement methods
Inspection of welds in-service
Inspection of flanged joints.

ASME B16.5 (Pipe Flanges and Flanged Fittings)

Scope
Pressure Temperature Rating
Materials
Dimension
System pressure Test

Day TWO

API 570 (Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems)

Scope & Definitions
Frequency and extent of inspection
Piping service classes
Inspection intervals
Extent of visual external and cui inspections
Inspection data evaluation, analysis, and recording
Corrosion rate determination
Maximum allowable working pressure determination
Repairs, alterations, and rerating of piping systems
Welding and hot tapping
Inspection of buried piping
Types and methods of inspection
Frequency and extent of inspection
Repairs to buried systems

Day THREE

ASME B 31.3 (Process Piping)

Scope and applicability
Service/Fluid Classification
Joint Quality Factors
Allowable stresses
Design for Internal Pressure
Design of permanent blanks
Impact testing for Low temperature service
Acceptance of Impact test results
Welding requirements-Preheat Temperatures
Post Weld Heat Treatment
Hardness Testing after PWHT
Inspection and testing
Non Destructive Examination Requirements
Acceptance Criteria
Leak testing-Hydrostatic
Leak testing-Pneumatic
Precautions during Pneumatic test
Service leak test
Thermal Expansion of Piping-Table C1

 

ASME B16.5 (Pipe Flanges and Flanged Fittings)

Overview of Pipe Flanges and Flange Fittings

Day FOUR

ASME Boiler and Pressure Vessel Code Section IX (Welding and brazing Qualifications)

Review of a WPS and PQR
Determine if WPS and PQR are in compliance with ASME Sec. IX
Essential and Nonessential Variables
Determine that the number and type of mechanical tests are correct tests
Determine whether the results are acceptable

ASME Boiler and Pressure Vessel Code Section V (Non-Destructive Examination)

Review of a WPS and PQR
Article 1, general requirements
Article 2, radiographic examination
Article 6, liquid penetrant examination
Article 7, magnetic particle examination (yoke and prod techniques only)
Article 9, visual examination
Article 10, leak testing

API Recommended Practice 574

Inspection of piping, tubing, valves, and fittings

Day FIVE

API RP 571 (Damage Mechanisms in the Refining Industry)

Brittle Fracture
Thermal fatigue
Erosion/Erosion Corrosion
Mechanical Fatigue
Vibration Induced Fatigue
Atmospheric Corrosion
Corrosion Under Insulation (CUI)
Boiler Water Condensate Corrosion
Fuel Gas Dew Point Corrosion
Microbiological Induced Corrosion (MIC)
Soil Corrosion
Sulfidation
Chloride Stress Corrosion Cracking (ClSCC)
Caustic Stress corrosion Cracking (Caustic Embrittlement)
High Temperature Hydrogen Attack (HTTA)

API Recommended Practice 577

Welding inspection and metallurgy

API Recommended Practice 578

Material verification program for new and existing alloy piping systems

FINAL

API 570 Full Mock-up Test, OPEN and CLOSED BOOK



Certified API 570 Piping inspectors must have a broad knowledge base relating to maintenance, inspection, alteration and repair of in-service metallic piping systems. The API 570 examination is designed to determine if applicants have such knowledge.
25-12-2019
Certified API 510 Pressure Vessel inspectors must have a broad knowledge base relating to maintenance, inspection, repair, and alteration of pressure vessels. The API 510 examination is designed to determine if individuals have such knowledge.
25-12-2019
Kiểm tra thẩm thấu mẫu khuyết tật từ các chi tiết nứt tự nhiên bằng thẩm thấu màu và thẩm thấu huỳnh quang
24-12-2019
Khóa đào tạo này tập trung vào việc củng cố và cải thiện các kỹ năng siêu âm, tần soát khuyết tật cho học viên đã được đào tạo kiểm tra siêu âm Level 1
24-12-2019
ĐÀO TẠO